Why long parts need support at both ends

A turntable positioner holds the workpiece at one end and leaves the rest of it cantilevered. That is fine for a short fabrication and wrong for anything long: a 3 m pipe clamped at one end and rotating will sag, whip and deflect — and the deflection changes the weld height once per revolution. On a long part, the sensible arrangement is a headstock that drives and a tailstock that supports, with the workpiece held between them.

The HT3 is that arrangement: a head-and-tail-stock positioner for pipe, tube, shaft and long cylindrical work, where both ends are located on centres or in chucks so the part turns true about its own axis.

HT3 head and tail stock positioner holding a long pipe between chuck and tailstock

Head and tail stock versus turntable

FactorHead and tail stock (HT3)Turntable positioner
Workpiece shapeLong, cylindrical, rotationally symmetricAny shape with a clampable face
SupportBoth ends — no cantileverOne end only — unsupported overhang
Runout on long partsLow — part turns about its own centresIncreases with overhang length
Access along the lengthFull — nothing in the way between chucksClear on top
Changing part lengthTailstock slides along the bedNot applicable
Bulkier or irregular workDifficult — needs centring features at both endsEasy

The deciding question is whether the workpiece has a centre at both ends. A pipe spool, a tube bundle, a shaft or a cylinder does. A fabricated frame does not, and belongs on a table.

How the two units work together

Headstock

The headstock carries the drive: a geared motor through a worm reducer to a chuck or face plate, with a hollow spindle where the work passes through. Because it both drives and locates, the headstock's chuck has to be concentric with the spindle — a chuck mounted on a worn spindle gives runout that no amount of tailstock adjustment can correct.

Tailstock

The tailstock provides the second centre and nothing else, which is its value. It slides along the bed to suit the part length and its quill extends to press the centre into the workpiece. Three practical points:

  • Alignment to the headstock centre. If the tailstock centre is even slightly high or offset, the part is held in bending. The bed has to be machined so both centres are on one line, and the alignment should be re-checked after installation and periodically.
  • Quill pressure. Enough to locate, not enough to bow the part. On thin-wall pipe, excessive quill pressure ovalises the end.
  • The bed. A single fabricated bed carrying both units is stiffer and easier to align than two separate bases bolted to a floor.

Rotation drive and welding current

Rotation is slow and controlled — a variable-frequency drive with a speed display, so surface speed can be set for the welding process. Welding current return has to go through a proper slip ring or brush on the headstock; through the chuck jaws or the tailstock centre it erodes both and destabilises the arc.

Head stock chuck holding a pipe end on an HT3 positioner

Applications

  • Pipe and tube welding — circumferential seams on long spools, held true at both ends.
  • Shaft rebuilding — hardfacing or welding a shaft while it turns about its centres.
  • Cylinder bodies — welding end caps and bosses on long cylindrical shells.
  • Roller and drum fabrication — where the part must run concentric for the seam to stay flat.

Specifying an HT3

We need: workpiece diameter and length range, weight, the centring features available at each end (chuck, centre hole, machined bore), the required rotation speed range and drive accuracy, whether a hollow spindle is needed for bar or tube to pass through, the welding process, and the shop layout including crane access along the bed length.

Positioners in the BIQEE range cover capacities from 0.5 t to 100 t with table and fixture sizes from 600 mm to 5,000 mm; head-and-tail-stock units are configured within that range against the workpiece list. Minimum order quantity is 1 set. Standard machines ship in 30–50 days after deposit; extended beds and special chucks are scheduled in the technical proposal. Payment terms are T/T; trade terms are FOB, FCA or CIF. Core ranges are CE compliant and supplied against a certificate of compliance.

Positioners are supplied under the BIQEE brand by DESAN ELECTRIC LTD, which has served 1,000+ customers in 20+ countries over 20+ years with welding engineering experience since 1997. For pipe work that also needs tilting, see the PP3 pipe weld positioner; for table work, see the FT3 floor table positioner.