Roll cladding: putting the wear resistance where the wear happens

A mill roll is a large, expensive, precision component that wears on its working surface. Replacing it is costly; rebuilding it is routine. Weld cladding restores the profile and applies a wear-resistant layer, and a purpose-built roller cladding machine is what makes that economically repeatable rather than a skilled manual job.

DESAN roller cladding machines cover rolls from 1 t to more than 50 t, with one, two or more welding heads so that one or two rolls can be clad at a time. The machines are built around a heavy-duty welded base that allows welding in all directions, with the head carried on a rigid column so the arc length stays constant through a long, slow cladding pass.

Roller cladding machine cladding a large mill roll with submerged arc weld overlay

The process chain on a cladding machine

1. Preparation and preheat

The roll surface is turned or ground back to clean parent metal and the cladding alloy has to bond metallurgically. Most hard alloys require preheat, and the preheat and interpass temperature windows are narrow: too cold and the deposit cracks at the fusion line, too hot and the hardness falls away. Temperature measurement during the pass is therefore part of the machine, not an operator's guess.

2. Cladding with controlled step-over

The roll turns slowly under a fixed head, or the head traverses while the roll turns, depending on the configuration. Bead pitch, oscillation width and travel speed together determine overlap and therefore whether the deposit is continuous and crack-free. Spiral cladding lays a continuous helix; circumferential cladding lays rings. Spiral is faster; circumferential gives more consistent thickness on a tapered roll body.

3. Cooling and stress control

A clad roll carries substantial residual stress. Controlled cooling — often under insulation — and, where the specification requires it, a stress relief cycle, are what prevent delayed cracking. This is process time, not machine time, and it is the reason cladding schedules are planned in days rather than hours.

4. Machining back to profile

The clad surface is left oversize and machined or ground to the finished roll profile. Deposit thickness allowance has to be specified up front: too little and the roll finishes undersize, too much and machining time and alloy cost rise unnecessarily.

Welding head cladding the surface of a rotating mill roll

Machine features that matter in production

FeatureWhy it matters
Multiple welding headsTwo heads cladding simultaneously roughly halves cycle time on a long roll body, or lets one roll be clad while another is prepared
Automatic stick-out adjustmentRoll diameter grows as cladding is deposited; a fixed head would drift out of the arc-length window over a long pass
Flux recovery systemSubmerged-arc cladding consumes large volumes of flux; recovery reduces consumption and keeps the working area clean
Temperature and dimension measurementPreheat and interpass temperature control, plus in-process diameter measurement to confirm deposit thickness
Data logger and parameter recordingTraceability per roll — the record that the customer's maintenance system needs
Fume filtrationCladding alloys generate significant fume; extraction is a health requirement, not an option
Error notificationLong unattended passes; an alarm by email means a fault is caught before a whole roll is scrapped

Wear patterns the machine is set up to match

Rolls wear differently depending on duty. Hot strip mill rolls suffer thermal fatigue cracking and abrasion; cold mill rolls wear by adhesion and abrasion; crushing rolls wear in a groove pattern from the fed material. The cladding programme — alloy, pattern (oscillating, stringer, square wave, chevron or spiral), and layer count — is selected against the wear mode. A hardfacing deposit laid in the direction of abrasive flow wears measurably faster than one laid across it, so pattern choice is part of the engineering, not a default setting.

Industries and components

  • Steel and general maintenance workshops — work rolls, backup rolls, table rolls, pinch rolls.
  • Cement and coal — vertical mill rollers and tables, crusher rolls.
  • Paper and pulp — press and dryer rolls where surface restoration is routine.
  • Pipe and cylinder bores — internal cladding using a bore cladding head on the same machine base.

Specifying a roller cladding machine

To quote one we need: roll diameter and body length range, roll weight, the cladding alloy and required deposit thickness, the wear mechanism being addressed, whether one or two rolls will be clad at a time, the required heads count, available floor space and crane capacity, and the quality records the customer's system requires. Where the roll has to be machined after cladding, that is normally a separate operation and is stated in the quotation boundary.

Minimum order quantity is 1 set. Standard machines ship in 30–50 days after deposit; customised machines and multi-head configurations are scheduled in the technical proposal. Payment terms are T/T; trade terms are FOB, FCA or CIF. Equipment is supplied against a certificate of compliance and core ranges are CE compliant.

Cladding and hardfacing machines are supplied under the ZAULUX and DESAN brands by DESAN ELECTRIC LTD, which has served 1,000+ customers in 20+ countries over 20+ years with welding engineering experience since 1997. For the flexible frame-based alternative, see the H-Frame hardfacing machine.