
Weld surfacing, sized to the workshop rather than to the plant
Hardfacing is the economics of putting expensive wear-resistant material only where it wears. A mill roll, a screw conveyor flight, a valve seat or a crusher hammer is made from ordinary structural steel and given a surface layer of hard alloy. The base carries the load; the deposit carries the abrasion.
The problem for most workshops is that weld surfacing machines are usually built as dedicated cells for one component family. An H-Frame hardfacing machine takes the opposite approach: a rigid frame carrying one or more welding heads, which is then mounted on whatever the workshop already has — a manipulator, a rotating table, a lathe bed, or simply a floor table. The same frame serves flat hardfacing, roller welding, spiral welding and multi-head work.

The frame, and why the mounting is the product
An H-frame is a stiff portal that carries the welding head on a cross-slide and a vertical slide, so the head can be positioned in two axes over the workpiece and then traversed along the weld. Mounted on a column-and-boom manipulator, the frame reaches into vessels and over large rolls. Mounted on a lathe bed, it turns an existing lathe into a hardfacing machine with the workpiece chucked and turned by the lathe. Mounted on a rotating table, it handles flat circular work.
That modularity is the practical answer to a workshop that hardfaces a variety of parts in modest quantities. Rather than one dedicated cell per part family, one frame is moved between host machines.
Weld patterns and what each one is for
| Pattern | Description | Used for |
|---|---|---|
| Stringer bead | Straight parallel beads with a set step-over | Building deposit thickness with minimal dilution; the standard first layer |
| Oscillating bead | Weave of set amplitude and frequency | Wide coverage per pass; controlling bead profile on flat surfaces |
| Square wave | Dwell at each side of the weave | Filling edges without undercut; keeping deposit thickness even at the weave extremes |
| Chevron | Zig-zag pattern along the axis | Deposits that resist a specific wear direction; used on crushing and mixing surfaces |
| Spiral | Continuous helix, typically on a rotating cylinder | Roll hardfacing and shaft rebuilding in one continuous pass |
Pattern selection is a wear-mechanics decision, not a cosmetic one. A crushing roll wears in a groove pattern; a deposit laid in the direction of the abrasive flow wears faster than one laid across it. Getting the pattern right for the wear mode is worth more than any increase in deposition rate.

Control and repeatability
Weld surfacing lives or dies on repeatability. A deposit that is 1 mm too thin wears through before the planned maintenance interval; one that is 2 mm too thick wastes expensive alloy and machining time. The control system on the H-Frame machines — supplied in either touch or pendant configuration — is built around fast set-up for a new component while holding the parameters that matter: current, voltage, travel speed, step-over, oscillation amplitude and dwell.
The practical gains:
- Repeatable programming — the same component hardfaced next month gets the same deposit as last month.
- Recorded parameters — where the customer's quality system requires traceability of the welding variables per component.
- Multiple heads — two or more heads running together on the same component, or on two components, multiplies output without multiplying floor space.
Typical configurations
- H-Frame on a manipulator — vertical mill rolls for the cement and coal industry, large shaft rebuilding.
- H-Frame on a rotating table — valves and circular components.
- H-Frame on a lathe — roller welding and screw conveyor flights, using the lathe for rotation.
- H-Frame on a floor table — flat hardfacing of plates, chutes and liners.
- H-Frame with multiple welding stations — volume production of flat wear parts.
- Internal pipe cladding — bore cladding of pipe and cylinder bores.
Specifying an H-Frame machine
To configure one we need: the components to be hardfaced with drawings and the deposit requirement (material, thickness, hardness), the host machine the frame will mount on and its interface dimensions, which welding process will be used (open arc, submerged arc, PTA or wire cladding), whether multiple heads are needed, and the required positioning axes. For roll work, the roll diameter and weight range and the available preheat arrangement have to be stated, since preheat and interpass temperature control are what prevent cracking in hard deposits.
Minimum order quantity is 1 set. Standard machines ship in 30–50 days after deposit; customised frames and host-machine interfaces are scheduled in the technical proposal. Payment terms are T/T; trade terms are FOB, FCA or CIF. Equipment is supplied against a certificate of compliance and core ranges are CE compliant.
Weld surfacing and cladding machines are supplied under the ZAULUX and DESAN brands by DESAN ELECTRIC LTD, which has served 1,000+ customers in 20+ countries over 20+ years with welding engineering experience since 1997. For dedicated high-volume roll work, see the roller cladding machines.