Two seam types, two positioning problems

Every cylindrical fabrication involves two kinds of weld, and they need different things from the equipment. A girth seam runs around the circumference: the workpiece has to rotate under a fixed torch, at a constant surface speed, with the joint held at the same height. A longitudinal seam runs along the length of the shell: the workpiece has to be held still while the torch travels along the joint, or the shell has to be clamped to a bed and the arc carried by a column-and-boom manipulator.

Shops that weld both on the same equipment need a positioner whose rotation axis is accurate enough for girth work and whose fixturing does not obstruct a longitudinal seam. That combination — rotation plus a stable, accessible bed — is what the general-purpose welding positioner in the BIQEE range is designed to provide.

Girth seam welding: rotation quality decides the weld

On a circumferential seam the arc is stationary and the workpiece moves. Every irregularity in rotation becomes a weld defect:

  • Speed variation changes heat input. A drive that surges or sticks at low speed produces alternating over- and under-penetration around the same joint.
  • Runout changes arc length once per revolution. On thin wall this means burn-through on one side of the shell and lack of fusion on the other.
  • Axial drift walks the weld off the joint line over a long seam.

This is why a positioner for girth work is specified on low-speed stability and torque, not on maximum rpm. A workpiece of several tonnes has to be turned at a surface speed measured in tens of millimetres per minute; the question is whether the drive can hold that speed without stalling or cogging, and whether the worm gear has enough self-locking to hold position when the drive stops mid-seam.

Long seam welding: the torch has to travel

A longitudinal seam is welded with the shell clamped flat and the arc carried along the joint. Three arrangements are used:

ArrangementHow it worksBest for
Positioner bed + column & boomShell clamped to the positioner table or bed; manipulator carries the torch along the seamVessels where the same machine must also do girth seams
Dedicated longitudinal seam welderFixed bed with a travelling carriage and a seam-following headHigh-volume shell production, one diameter family
Turning rolls + manipulatorShell on rotators, torch on a boom; the rotators are used only for girth workLarge vessels where longitudinal seams are made before rolling

The positioner-plus-manipulator combination is the flexible answer and the one most mixed shops choose, because one machine covers both seam types and the manipulator is also useful for internal welding and inspection access.

Clamping, and why it defines distortion

A longitudinal seam pulls as it cools. If the shell is not clamped to a straight reference during welding, the finished shell is not round — and a shell that is not round will not fit the next course. Strongbacks, copper backing bars and hydraulic clamps along the seam are standard; the positioner's job is to give a flat, rigid bed to clamp against, with T-slots or clamping rails at a usable spacing.

What to look for in a general-purpose positioner

  • Worm gear drive with self-locking — holds the workpiece at any angle with power off.
  • Tilt range covering at least 0–90°, with the table able to stop and lock at intermediate angles. For work that must go past vertical (dished ends, nozzles), a machine with a range beyond 90° is needed.
  • Table with T-slots or a tapped grid — a bare plate table forces improvised clamping, which is where distortion and accidents come from.
  • Earthing through a proper slip ring — never through the bearings.
  • Remote pendant with speed display — the operator has to set surface speed, not guess at rpm.

Applications

General-purpose positioners with both girth and long-seam capability are used in pressure vessel shops, tank fabrication, pipe spool assembly, wind tower internals, chemical equipment and general engineering fabrication — anywhere a cylindrical or box workpiece has to be presented flat for welding and rotated between passes.

Specifying a positioner for mixed seam work

To quote one we need: workpiece diameter and length range, maximum weight, wall thickness and material, which seam types will be run on the machine and in what proportion, the welding processes, whether longitudinal seams need clamping rails or a backing arrangement, and the required tilt range. Capacities in the positioner range run from 0.5 t to 100 t, with table diameters from 600 mm to 5,000 mm; the specific configuration follows from the workpiece list.

Minimum order quantity is 1 set. Standard machines ship in 30–50 days after deposit; customised units are scheduled in the technical proposal. Payment is T/T; trade terms are FOB, FCA or CIF. Core ranges are CE compliant and supplied against a certificate of compliance.

Positioners are supplied under the BIQEE brand, turning rolls under DESAN, combination welding machines under ZAULUX, all contracted by DESAN ELECTRIC LTD. The company has served 1,000+ customers in 20+ countries over 20+ years, with welding engineering experience since 1997.