The cylinder is the muscle behind every positioning machine

A welding positioner that lifts, a rotator that adjusts its roller centres hydraulically, an H-beam line that clamps a web, a press frame that closes — all of them convert electrical power into linear force through a hydraulic cylinder. On positioning and welding equipment the cylinder is also the component most likely to decide whether the machine holds position safely when power is lost.

DESAN ELECTRIC supplies hydraulic cylinders for its own positioning, lifting and clamping equipment and for customer machinery, covering the standard constructions used in industrial and mobile applications.

Hydraulic cylinder with chrome plated rod and welded end connections

Cylinder types and where each is used

TypeCharacteristicTypical application
Welded cylinderWelded end caps, compact, cost-efficientGeneral industrial lifting, clamps, positioning machine lift axes
Tie-rod cylinderRepairable, serviceable sealsMachine tools, equipment where maintenance access matters
Telescopic cylinderLong stroke from a short retracted lengthTipper bodies, lifts with limited mounting space
Double rod endEqual force and speed in both directionsSynchronised clamping, opposed motions
Locking cylinderHolds position mechanically on loss of pressureSafety-critical holding — elevated loads, tilt axes
Rephase cylinderSelf-synchronising multi-stageMulti-stage lifts that must extend in step
Ram cylinderSingle-acting, large force, short strokePresses, jacks, heavy lifting
Integrating valvingValve block integrated into the cylinderCompact circuits, reduced piping
Linear feedbackIntegrated position measurementClosed-loop positioning axes
Screw actuatorMechanical screw drive within a cylinder formHolding under load without hydraulic pressure
Aluminium cylinderLight weight, corrosion resistantMobile equipment, weight-sensitive installations
High-force / customBuilt to the applicationNon-standard mounting, stroke or force requirements

Selection: the five parameters that decide the cylinder

  • Force and pressure. Bore diameter follows from the required force at the available system pressure — and on the retract side, from the rod diameter reducing the effective area. A cylinder specified only on push force can come up short on the return stroke.
  • Stroke and mounting. Clevis, flange, trunnion and foot mountings each impose different bending loads on the rod. A cylinder loaded in bending rather than pure axial compression will leak at the gland long before its rated life.
  • Speed and flow. Cylinder speed is set by flow divided by area, not by pressure. A cylinder sized for force but fed through undersized ports will cavitate and judder.
  • Environment. Outdoor, washdown, high-temperature or corrosive atmospheres change the rod material (chrome thickness and finish), seal compound and paint specification.
  • Holding and safety. Any axis that can drop on power loss needs either a pilot-operated check valve, a hose-burst valve, or a mechanically locking cylinder. On a welding positioner with an elevated workpiece, this is a personnel-safety requirement, not an option.

Rod finish and seals

Most cylinder failures start at the rod seal. Hard chrome plating on the rod resists abrasion and corrosion; the surface finish has to be fine enough for the seal to wipe cleanly without carrying grit into the gland. In dusty or spatter-heavy welding environments, a rod bellows or wiper is worth specifying — weld spatter on a chrome rod destroys the seal on the next stroke and the cylinder then leaks oil onto the workpiece.

Hydraulic cylinder assembly with mounting clevis and hydraulic ports

Cylinders on welding equipment specifically

Three requirements recur across positioning and welding machines:

  • Holding position without drift. A tilt axis on a positioner must not creep while the operator welds. That means either a self-locking mechanical arrangement or a hydraulic lock that holds against the full load with the pump off.
  • Smooth low-speed motion. A hydraulic lift that moves in steps produces a step change in welding torch height. Smooth low-speed control depends on cylinder friction characteristics and on using a proportional valve rather than a simple directional valve.
  • Rigid mounting. A welding head mounted on a hydraulically positioned arm inherits any compliance in the cylinder and its mounting. Arc length stability starts at the mechanical structure, and a soft mounting shows up as bead width variation.

Specifying a cylinder

To quote a cylinder we need: required force and direction, system pressure, stroke, mounting type and interface dimensions, speed, operating environment, any holding or safety requirement, and the fluid and temperature range. Non-standard cylinders are built to the application drawing.

Minimum order quantity is 1 set for equipment; cylinders are quoted per unit or per batch. Standard equipment ships in 30–50 days after deposit. Payment terms are T/T; trade terms are FOB, FCA or CIF. Components are supplied against a certificate of compliance.

DESAN ELECTRIC LTD supplies hydraulic cylinders, power packs and hydraulic equipment alongside its welding positioning ranges, and has served 1,000+ customers in 20+ countries over 20+ years with engineering experience since 1997. All enquiries are handled by DESAN ELECTRIC LTD.